Tuesday, November 7, 2017

Still time for the Ultimate Xmas gift: Benchcrafted Classic Workbench


We have for sale a freshly-built-to-spec example of our Classic Workbench. Made entirely of hard rock maple, it's outfitted with our Classic Leg Vise w/Crisscross, Planing Stop and one Hand-forged Holdfast, For full specs and photos, see our Classic Workbench Plans page. This bench is built exactly to the specs listed.

The bench is in the white, that is, we didn't apply any finish to any of the surfaces. You can either leave it that way or apply a finish of your choice (we hope you leave the top unfinished, or at most one coat of oil.) The bench is completely assembled and ready to use. 

The Benchcrafted Classic Workbench is constructed entirely with in-compression-for-eternity drawbored mortise and tenon. It's as solid as humans can make it, short of growing a tree in the shape of a bench. The bench is built to the highest standards of traditional German craftsmanship in the utopian village of Amana Iowa. Our collaboration with the craftsmen in Amana, along with our experience in traditional workholding has yielded a workbench that is truly heirloom quality, but offered at what we think is a very reasonable price. There are other bench makers out there who are offering stunning museum-quality, marquetry-encrusted benches with our hardware and designs (Frank Strazza and Mark Hicks among others.) We consider our flagship Split-Top Roubo as nearing the pinnacle of bench design (if there is such a thing) but we wanted to offer an essential bench built to high standards--an approachable but bulletproof tool for passionate enthusiasts that are perhaps just getting into the craft. Our principle bench maker has been building furniture at the Amana Furniture Shop for nearly 50 years. Needless to say, 150 years of woodworking tradition in Amana directly back to 19th century Germany speaks for itself. Many of the Amana craftsmen are multi-generational woodworkers.

The bench is available for pickup in eastern Iowa (contact us for details) or white glove delivery, in which the bench is wrapped in moving blankets, transported in a moving van used for furniture delivery only, then unloaded at your address and brought inside by the delivery techs. It costs a bit more to ship this way, but less than you might imagine.

Price is $2600. Delivery fees extra. Delivery typically takes about 2 weeks.

If you're opening a school, community shop, woodworking club or refitting an existing facility with worn out or poor quality benches, please contact us, we can supply you. 

To purchase this bench, send us an email with your contact info to: info@benchcrafted.com

Monday, October 30, 2017

Video: Hi Vise Build



Watch Guy Dunlap build our Hi Vise in this excellent video from our friends at Highland Woodworking.

Hi Vises are in stock and ready to ship.

Tuesday, August 22, 2017

Handworks

Just a short compilation video from Handworks 2017


Wednesday, August 16, 2017

Videos: Build A Bench With Our Hardware


Image courtesy of Lost Art Press

We're often asked if we'll ever offer a bench building video, or complete videos on how to install our vises. And the answer is, not anytime soon. You may be wondering if this is shortsightedness on our part, lack of interest, or that we're too cheap to shell out the money for a video studio, which is significant. The reason is, there are others out there who can do it better than us. Here they are.

Marc Spangulolo, aka The Wood Whisperer
https://thewoodwhispererguild.com/product/split-top-roubo-workbench/

Marc was the first to make a serious video on building our Split Top Roubo. Marc's video skills and presentation are excellent. You won't find a more comprehensive and easy to follow series than Marc's. For $110 you get almost 10 hours of instruction covering every aspect of the build, and the vise installation, along with printed plans. It's an excellent value. Marc also includes videos on retrofitting a Crisscross and our latest Glide, in addition to the original Glide leg vise. 

Chris Schwarz and Will Myers

In this video ($35) Chris and Will not only build a bench together (featuring our Classic Leg Vise), but discuss different ways of getting there. There's some pretty funny moments too. Definitely worth the watch even if you're not building a bench. 

Guido Henn at Fine-Tools.com
https://www.youtube.com/watch?v=sZ4doJvy_5w

Guido has two excellent videos (in German) on the installation of our Glide Leg Vise and Tail Vise. Although the videos are in German, they are mostly without narration and subtitles, and the video quality is excellent, providing a clear view of each step of the process. The third video is a tour of the bench, in English. 

Matt Estlea

Matt studies furniture making in Oxford, England. Follow along as he build "Bertha" his Roubo bench outfitted with Benchcrafted vises. Excellent production quality.

KC Woodworks

Some good enthusiast content here. Watch as Kev makes a Hi Vise and retrofits a friend's bench with a Glide. 

Tom Fidgen

Not so much an instructional video, but nice to watch nonetheless. Very relaxing. Watch Tom build and assemble a Moxon vise entirely with hand tools. 

Mike Bandte

An ongoing series of Mike's Split Top Roubo build, in German. Mike also has a series on building our Moxon vise. 

There are many others out there, and a "Benchcrafted" search on Youtube will yield loads of results.






Thursday, June 15, 2017

There and Back Again.........Moxon wood

A few years ago we offered complete Moxon kits, the hardware and all the wood needed to make a complete vise, milled and ready to go.  It wasn't fancy, but all the parts were there to spec and all the holes drilled.  We offered this mostly because there was a demand.

At some point we got so busy we simply couldn't do this anymore, other things were taking our time.  We still get requests though, so in that vein, we are now offering these kits once again.  The new kits are a shade nicer than the old ones, still made from hard maple but these are finished just a smidgen better and the stabilizer batten now comes glued up to the rear chop.

So here wee are again, the complete kits are ala cart on our Store page.


Unsolicited Plug

We don't really plug other products much.  But on occasion we like to toot a horn about this or that.

At Handworks recently we met Janet Switzer of Camp Robber canvas.  We immediately liked her wares and started thinking of things to make.

One of the things on the top of our list was a flat bottomed satchel in heavy duty waxed canvas for the trunk of our cars.  I shot her some dimensions and within a week (!) had a bag in my hand.  Not only was it spot on what I had in mind but it is built like a tank.  I can't imagine it ever wearing out.  These would make an excellent tool bag.

Her Instagram is here and her Etsy store is here.






Video: Swing Away Seat



We shot this short video to show our new Swing Away Seat in action. We have them in stock and ready to ship.

Further details here.

Tuesday, June 13, 2017

Lost and Found: temporary post

We're going to leave this post up for a short while only.

Someone left a camcorder battery (looks to big for an SLR) on our bench at Handworks.

If this is yours let us know.



Monday, June 12, 2017

Swing Away Seat Instructions


We've uploaded the installation instructions for the Swing Away Seat. We offer some tips and guidelines for installation, as well as fastener recommendations (which are not included with the seat.) We suggest you read up on the installation while waiting for you seat to arrive so you can have your hardware in house when the seat arrives.

Download the document here.

Also available on our downloads page.

Thursday, June 1, 2017

New Mag-Bloks

A week of new stuff in our Store page.

Brand new Mag-Bloks, Quartered White Oak, Quartered Sycamore and Spalted Maple now regular stock items.  Clockwise from upper left:  Quartered Sycamore, Spalted Maple, Quartered Oak.



For Sale: Fresh Classic Workbench


We have for sale, for immediate delivery or pickup, a freshly-built-to-spec example of our Classic Workbench. Made of hard rock maple (rock on!) it's outfitted with our Classic Leg Vise, Planing Stop, Hand-forged Holdfast, and Swing Away Seat. For full specs, see our Classic Workbench Plans page.

This bench was completed a couple weeks ago on May 15, displayed in our booth at Handworks, then placed back in storage. The bench is in the white, that is, we didn't apply any oil/varnish shellac to any of the surfaces. You can either leave it that way or apply a finish of your choice (we hope you leave the top unfinished, or at most one thin coat of oil.)

The bench is assembled entirely with in-compression-for-eternity drawbored mortise and tenon. It's as solid as humans can make it, short of growing a tree in the shape of a bench.

The bench is available for pickup near Cedar Rapids, IA (contact us for details) or white glove delivery, in which the bench is wrapped in moving blankets, transported in a moving van used for furniture delivery only, then unloaded at your address and brought inside by the delivery techs. The first time you touch the bench will be to use it. It costs a bit more to ship this way, but less than you might imagine.

Price is $2600. Delivery fees extra. Contact: info@benchcrafted.com SOLD

Now Available To Order: The Benchcrafted Swing Away Seat


After over a year of development, we're excited to announce our Swing Away Seat is available to order. To read more about the development of the seat, read this.



The Swing Away Seat is cast in gray iron and powder coated in satin black. When you buy the seat you'll receive two castings: the larger part called the mount, and the smaller part which bolts to your bench, called the bracket. You'll also receive two black oxide-finished steel pins that marry the parts together. They are loose pins, just like you'd find in a door hinge. So if you need to remove the mount from the bench for whatever reason, you simply lift the two pins and the mount comes off.

Mounting the seat to your bench or table is easy with two 1/2" lag screws or through bolts. Bolts are the stronger option, and if you've got 3" or less of wood to bite into, we recommend bolts. Lag screws, driven into properly-sized pilot holes in hardwood are extremely strong. However, since we can't control your mounting situation or skills, we can only make general suggestions. As such, the Swing Away Seat does not come with mounting hardware. Be wary of hardware store and home-center lag screws. They are usually total junk (but  not always) with soft steel and shallow threads. We source ours from the excellent Blacksmithbolt.com. The 1/2" square head lags in black oxide work very well with the Swing Away seat. We also recommend their rub washers under the head of lag screws for a smooth connection. These aren't so necessary with through bolts. For further installation info, download the Swing Away Seat document from our downloads page.


The Swing Away seat is  available two ways. Castings only, for us woodworkers who want to make our own seats, or packaged with a finished, ready to mount wood seat. The wood will be offered in one species only, quartersawn white oak with a chestnut stain and satin lacquer finish. The seat is 11" in diameter and ~1" thick. Each wood seat will include three screws to attach it to the mount.


Like our vises, the Swing Away seat is overbuilt. We haven't done any testing on how much weight the casting can take before it breaks, but our empirical knowledge tells us its more than anyone need worry about. Since the seat is cantilevered off its mounting surface, one does have to be mindful of the mounting structure. Obviously a free-standing structure could be prone to tipping, depending on the weight of the structure and the sitter. Again, there are lots of variables at play here that we can't possibly anticipate. Our Classic Workbench (pictured here) is not a super heavy bench, being somewhat narrow at 20" with a 3" thick top. Yet it supports a 250 pound body (me) without tipping. If you're planning to use one of these on any free standing object, keep this in mind. Again, see the installation document for further details. The Swing Away seat will pivot a bit over 180 degrees.

The Swing Away Seat is $199.

The Swing Away Seat with quartersawn oak seat is $249.

You can order through our Store Page.






Tuesday, May 30, 2017

Wednesday, May 10, 2017

Win a Hayward Bench at Handworks, But Only If You're Short


We wanted to do something special for Handworks 2017, so here's what we came up with. A bench for kids!

Vol. 4 of "The Woodworker" features a basic bench as its first article. We had three planks of yellow pine gathering dust in the corner, so we tossed together this bench over a couple days last week. It's 24" high, which should be perfect for a wide range of kids. To scale it down, we drew the major components in Sketchup full size, then scaled the model down based on the shorter height. It scaled great. Joinery is half lap dadoes on the front and read skirts, and a pair of 10mm Dominoes in each joint.

It's outfitted with our Hi Vise, which makes an excellent leg vise for smaller full size benches, or obviously for kids' benches too.

The bench will go home with one kid, free of charge, courtesy of us!

Here's how to win the bench (parents, read this to your kids).

We'll have a piece of clear, easy to plane basswood chucked in the vise. With a sharp Stanley #3 that we'll leave on the bench, the kid will try their best to make a full width, full length shaving from the edge of the board, under the coaching of their parent or us. They should practice making the best shaving they can. Once they are ready to make their final excellent shaving, they'll write their name on the edge of the board, plane it off, and put the shaving in a box. On Saturday afternoon at 3pm we'll draw one shaving and that kid will go home with the bench.

There are only two rules:

1. The kid must not be taller than 54".
2. One shaving per kid goes in the box.

Parents feel free to make the final perfect shaving for your kid if they can't. Hopefully that kid will win the bench so they can practice back home.









Thursday, May 4, 2017

Handworks........is the Midwest just too far or remote?



Handworks is now just 2 weeks away.  This will be the third bi-annual event and as we've said many a time before, you never know when there will be another.  Though we've followed the bi-annual pattern so far, we literally never know if there will be another one until some months later.  So if you are on the fence, better act if you can.

In the past, and probably still now, there have occasionally been some comments like "why Iowa?" or "it's too far from the coasts".   To be frank, we never really doubted that people would come to the Midwest, or anywhere really, if the event had the right spirit.  That said, we can understand some of the apprehension concerning travel and expense.  With that in mind here are a few points of interest:

- It's free
- It's in an historical village with a rich woodworking history
- It offers something for everyone, literally, if you or someone with you can't find something of interest in Amana or at one of the event venues then you probably have a hard time finding interest anywhere.
- It's low key (yes it can get crowded but in a good way)
- It offers a chance to both handle tools and learn quite a lot from a group of vendors that overall are more interested in craftsmanship than they are money.  You would be hard pressed to find another event that offers the same kind of hands on with so many experts short of a lot of dedicated, costly and time consuming classes
- There's even a dedicated section of the camp ground set aside for HW attendees


As for travel and attendance.  Yes, it can get crowded, registration is well over double the previous event, but we've spread things out this year into 5 venues, which should really make things nice.

As for travel, few of us in the States can complain (although we do have some people coming from AK).........Internationally we have registrants (aside from vendors) from Canada, British VI, UK, Germany, France, Norway (10!) Australia and get ready for it.......Indonesia.  So if these folks think it's worth the time and expense the least we can do is appreciate that the Midwest is equally far from everyone ;-)

See you there.

Monday, April 10, 2017

UPDATE. Miter Jack Kits: Metal Bits Now Available








Nick at Lake Erie is taking pre-orders for another small run of wooden bits. We've got a handful of the metal bits left from the first run. You can order the metal bits from us anytime (see our store page), but to get the wooden screw and threaded nut block, you'll need to pre-order through Lake Erie. More info here.

We've sold out of the La Forge Royale Miter Jack kits, but there's a silver lining. We made a double run of the metal bits which we're offering for sale. All you'll have to make is the wooden screw, and tap the nut block. The inexpensive wood threading kits will work (if you have a lot of patience) but we like the Beall products. The 1-1/4" is the one to get. If you don't want to bother with the threading, we recommend you contact Nick at Lake Erie Toolworks, who makes the best quality wood threads in the world.

The contents of the Miter Jack Kit Metal Bits are pictured above (minus the wood screw and nut block of course.) All the metal bit are manufactured in the USA by us. You'll also get a pouch with all the various screws needed to assemble the jack.


SOLD OUT: We have just 3 kits left, they do not include the various small wood screws and the groove pin (see below). Price is $30 plus shipping. If you want one just shoot us an email and we'll invoice you. Domestic shipping will be assumed unless otherwise noted.


Slotted Flat Head Wood Screws

#14 x 3" Qty: 4
#12 x 1-3/4" Qty: 8
#8 x 3/4" Qty: 3
#12 x 3/4" Qty: 1
#12 x 2-1/2" Qty: 2
#10 x 3/4" Qty: 1

3/16"dia. x 1" Center Groove Dowel Pin Qty: 1
Dowel pin available from McMaster Carr. Part # 98400A245
https://www.mcmaster.com/#98400a245/=17e8zjn

Monday, March 27, 2017

Crisscross Solo Blems


Just a heads up in case you're in the market for a Crisscross Solo and you're coming to Handworks.
We'll have a few blems available at the event for a discount price of $79. We usually don't have to offer blems or seconds because we usually catch them early on in the process. This time a few Crisscross arms made it all the way through powder coating. Here's the issue with these. During the casting process the moulds get transported from the mould-making area to the pouring deck and every now and then a mould gets jarred and makes the lines in the castings you see above. It's completely cosmetic. The arms function as intended. A few of the arms got the royal treatment at the powder coaters as well. The middle one above shows the result. You may need to run a file or drill bit through the holes to get the pins to pass. These will be priced at $79 and are available only at Handworks. If we have leftovers, we'll post them here for sale after all the hubbub is over.

Friday, March 24, 2017

The Benchcrafted Swing Away Seat


After over a year of development, we're excited to announce pricing and availability of our Swing Away Seat!

But first a few words about this product in case some of you are wondering what road we're headed down. When we started Benchcrafted it all began with a product that, although made of wood, was not a woodworking tool. The Mag-Blok. Only after we got a wild hair to build a new workbench for our shop did we take the leap in manufacturing our own woodworking vises. So, although we've become known as the "men of vise" we have our roots in making stuff we like to use, period. The other tools in our line reflect that philosophy too. We use everything we make, often on a daily basis. The Swing Away Seat is no different. And it just so happens that it's an incredible workbench accessory as well.

In early 2012 we began researching these seats after discovering a vintage example at a local food market. We were intrigued by the whole concept. How sweet would it be to have a seat for your bench that was always there, but also "never" there? We began compiling designs and searching the old patent record. Fast forward to last year. Prodded by our customers, we decided to put the Swing Away Seat at the head of the line. As is typical, it took way longer than we anticipated to complete the first run. A dead simple device, but there's more here than meets the eye. We also wanted to spend some time designing the thing so it didn't only look like something old.



The Swing Away Seat is cast in gray iron and powder coated in satin black. When you buy the seat you'll receive two castings: the larger part called the mount, and the smaller part which bolts to your bench, called the bracket. You'll also receive two black oxide-finished steel pins that marry the parts together. They are loose pins, just like you'd find in a door hinge. So if you need to remove the mount from the bench for whatever reason, you simply lift the two pins and the mount comes off.

Mounting the seat to your bench or table is easy with two 1/2" lag screws or through bolts. Bolts are the stronger option, and if you've got 2" or less of wood to bite into, we recommend bolts. Lag screws, driven into properly-sized pilot holes in hardwood are extremely strong. However, since we can't control your mounting situation, we can only make general suggestions. As such, the Swing Away seat does not come with mounting hardware. Beware of hardware store and home-center lag screws. They are usually total junk with soft steel and shallow threads. We source ours from the excellent Blacksmithbolt.com. The 1/2" square head lags in black oxide work very well with the Swing Away seat. We also recommend their rub washers under the head of lag screws for a smooth connection. These aren't so necessary with through bolts.



The Swing Away seat will be offered two ways. Castings only, for us woodworkers who want to make our own seats, or packaged with a finished, ready to mount wood seat. The wood will be offered in one species only, quartersawn white oak with a chestnut stain and satin lacquer finish. The seat is 11" in diameter and 1" thick. Each wood seat will include three screws to attach it to the mount.


Like our vises, the Swing Away seat is overbuilt. We haven't done any testing on how much weight the casting can take before it breaks, but our empirical knowledge tells us its more than anyone need worry about. Since the seat is cantilevered off its mounting surface, one does have to be mindful of the mounting structure. Obviously a free-standing structure could be prone to tipping, depending on the weight of the structure and the sitter. Again, there are lots of variables at play here that we can't possibly anticipate. Our Classic Workbench (pictured here) is not a super heavy bench, being somewhat narrow at 20" with a 3" thick top. Yet it supports a 250 pound body (me) without tipping.  If you're planning to use one of these on any free standing object, keep this in mind.

The Swing Away seat will pivot a bit over 180 degrees in total.

Pricing and Availablity

The Swing Away seat will be available initially at Handworks in Amana, IA, May 19-20. After the event is over, we'll post them to the website where they can be ordered any time. The Swing Away seat will be a stock item. We won't be taking pre-orders or deposits for the seats we sell at Handworks or later online. If you want to make sure you get one of the first ones, be at our space in the Festhalle Barn first thing Friday morning, May 19. We'll take credit cards, but cash will get you in and out of our space much quicker. Unfortunately we can't reserve a seat for you before the doors open, or hold one after you've paid. You'll want to take your seat back to your vehicle immediately since they are a tad on the heavy side. We will have both the seat only, and seats with wood for sale. We'll have several seats mounted to benches for you to try out at Handworks.

The Swing Away seat is $199.

The Swing Away seat with wood is $249.

See you in Amana...




Monday, February 20, 2017

Build A Bench with Jeff Miller this April



If you'd like to spend a couple weekends building a Roubo-style bench with Jeff Miller, here's your chance.

Over two weekends (March 31-April 2, and April 7-9) Jeff is offering the class at his shop in Chicago where you'll get instruction from one of today's best modern furniture makers. Jeff has extensive experience building this bench, and installing our vises. Most of the benches in Jeff's shop are outfitted with our stuff, and he has an intimate knowledge of how they install and function. Although Jeff will help you build a bench with whatever vises you wish, not just our stuff.

Jeff is also one of our favorite people. Always good-humored and cheery, two weekends with Jeff building stuff sounds like serious fun. And you'll walk away with not only a fine bench, but also a bunch of new skills and techniques.

For more info, see Jeff's website here. http://www.furnituremaking.com/workshophome.html

Photo by Narayan Nayar at FORP II.

Friday, February 3, 2017

Lead times, Crubber and dealers

First lead times.  Many of you may notice that in the past we have posted individual lead times for most of our products, especially vise products.  A short while back we changed this to nearly immediate shipping on all products because our production times have improved.  Most orders now ship within a couple days (and many of them ship the same day).

We tend to get a fair share of complaints when things aren't shipped immediately (like when we are closed for short breaks, which is fairly rare for us).  We apologize for these sometime delays.  On the other hand we rarely get any kudos for prompt order fulfillment.......that's ok though, we're used to it ;-)  We think the vast majority of our customers would give us high marks for the speed with which we not only fill orders but the lengths we often go to with special requests and responding to emails.

Crubber.  The demand for Crubber has been high.  That said, vise orders take priority for this stuff so that's where it goes first.  You will note that the ala cart Crubber now has a lead time.  We don't produce Crubber, so we have to wait just like you do.  We encourage anyone who needs to place a mixed order to make their Crubber order separate to speed up your order fulfillment, unless you are willing to wait, we won't ship other items in an order until the Crubber is in stock.

New dealers.  We have two new dealers, one for vise products the other for Mag-Bloks.

Vises.  Though they have actually been a dealer for about 2 years! we haven't added them to our dealer list merely out of stupid neglect.  Harvey is our China dealer and we're happy too say the dealer for MANY of our peers in tool making (Lie-Nielsen, Veritas, Bridge City, just to name a few).








Australia.  No specifics yet but we may be close to establishing a dealership in Australia.  We ship an inordinate amount of vise products to AUS/NZ and it's time we had a dealer there for our customers sake.

Mag-Bloks dealer.  We're happy to add The Cook's Edge of Prince Edward Sound to our Canadian dealer list for Mag-Bloks.  Quite a few dealers up North now so seeing a Blok in person is getting easier all the time.

Tuesday, January 24, 2017

An Update for 2017


Last year was incredibly busy here at Benchcrafted. We designed and released several new things. The Classic Workbench Plans, the Hi Vise, the Planing Stop and we made good progress on the new "bench seat" (still haven't settled on a name yet.) We didn't have much time to blog about personal woodworking projects (which are always in the works here in the Benchcrafted test shop) but we hope that will change this year.

You might be wondering about our swinging bench seat, which we started developing about a year ago. It's moving along. To produce this at a reasonable cost we've had to spend loads of time designing it for efficient machining, then building the fixture for machining as much as possible in one setup. We're working on that right now. The brackets that hold the swing arm to the bench are 75% done. Right now we don't have an ETA on these, or a price. That said, if you're coming to Handworks 2017 expect to see these for sale in our booth. And if they are done sooner, of course we'll get them posted.